››››     DISK2XFD v0.90 Copyright 1994 Ken Siders›     This program is freeware and my be distributed, but not sold.  The›     only restricition is the file DISK2XFD.ARC is kept intact and›     unchanged.›     ›     DISK2XFD.COM - the program›     DISK2XFD.DOC - this file›     ›     From now on DISK2XFD will be referred to as D2X.›     ›                                 Introduction›     ›          D2X will convert a single sided single, enhanced, or double›     density disk to XFD format for use with PC-Xformer.  I believe›     ST-XFormer also uses the same file format.  The output can be to a›     disk file (on the same or different disk) or via XMODEM to an R:›     device.  All you need to use to use Xmodem is to append D2X to an R:›     handler (or be sure one is booted) and specify R: as the output file,›     link the two computers together, and have a terminal program on the›     other side that has Xmodem receive.  D2X uses standard XModem with a›     checksum not the XModem-CRC.  If anyone wants CRC or other protocols›     send me info on how the CRC code is calculated as well as other›     differences.  It is up to you to get an interface and rig up a null›     modem cable.  This is descibed in many sources and not repeated here. ›     I could provide docs on how to build an interface using a›     max232/icl232 ic, a 74LS03 ic, and few support components.  I actually›     built one into DB9 hood that has a IBM compatable output (with 9 pin›     ports).  I don't think I would ever try this again though.  Although I›     build this one myself using a SX212 to figure which SIO pins are used›     for which functions. I believe this type of interface is described›     somewhere.›     ›                              D2X to a disk file›     ›          The format to use is:›     DISK2XFD [options] outputfile›     ›          With Atari or MyDos you will be prompted for the [options]›     outputfile part with a "DISK2XFD>" prompt.  The output file must›     specify the disk number use D1:name (or any other drive) not D:name or›     name.  D2X uses the drive to find out if disk swaps will be required. ›     Options are:›       -Sn Set source drive (n is 1 to 8).  The default is drive 1.  The›     drive must be a real drive or an O.S. simulated RAM drive that›     emulates a real one.  DOS type RAM drives will not work since they are›     only emulated on the CIO level and not SIO level.›     ›       -W  causes DISK2XFD to reprompt when done so you can translate›     multiple disks without reloading the program.›     ›          Caveats:  Even though the file size is a multiple of 128 bytes,›     Bobterm and possible others adds an extra block to the end, making the›     filesize 128 bytes bigger and XFormer would not recoginize it as a››››››››››››››     disk.  I tried De-term and it did not append the extra bytes. ›     Hopefully future versions of XFormer will be more flexible about disk›     and file sizes.›     ›          If the source and destination is the sam drive, you will prompted›     for disk swaps.  D2X compresses blank sectors in memory to save disk›     swaps on disks that are not full.  This does slightly slow disk›     writes.  Future versions won't compress empty sectors if swaps are not›     required to speed output.›     ›                                   D2X to R:›     ›          The line format is the same as above except with additional›     options listed below.  The following options are ignored on disk›     output.›     ›       -R Reduce Timeout.  The disk will be read and written in small›     chunks.  Use this option if XModem times out on the receive end›     waiting for the slow atari disk drives.  Most terminal programs can be›     configured to eliminate this by increasing the maximum number of›     retries, but some probably can not be.›     ›       -Bnn Baud rate.  Sets the baud rate to send.  Default is 19200 baud›     (this will usually be 9600 baud on devices not supporting 19200 baud).›     Values are: 15=19200 14=9600 13=4800 12=2400 10=1200 8=300.  These is›     the value stored in aux1 on an xio 36 call.  Other values may be›     possible - see your manual.  The baud rate of D2X must match that of›     the reciever.›     ›          After the option, use R: as your output file.  Do not start the›     receiver yet.  Start up D2X with the appropriate options and R: as the›     filename.  The disk will be read and you will receive a message›     telling you it is waiting for the destination.  On the receiving›     computer, Start XModem Download.  This must NOT be XModem-CRC but›     standard Xmodem (or XModem-Cksum).  To abort the transfer any time,›     press and hold OPTION until the transfer is cancelled.  This should›     automatically abort the receiver.  If it doesn't, manually abort the›     receiver.  You should also be able to abort a transfer on the receiver›     in.  If D2X doesn't abort wither press OPTION on the Atari or type a›     couple control-X's on the receiver.›     ›          Caveats: D2X does not add extra data to the end of the file so›     the problem mentioned above does not exist.  The biggest problem is›     that some terminal programs may not support standard XModem.›     ›                            Additional Information.›     ›          This program was tested on an Atari 800XL and a 1050 disk drive›     with US-Doubler.  The serial interface was a home build interface›     (Rverter or SX212 type).  It was tested with the BobVerter handler›     from Bobterm.  On the IBM end I used Crosstalk for windows as the›     receiver.  I couldn't use the terminal program that comes with Windows›     because it only supports XModem-CRC and YModem.  I had no problems››››››››››››››     with transfers up to 19200 baud.›          It should work with any 850 compatable R: handler that doesn't›     occupy any memory above location $2400.  Some interfaces may not›     support rates above 9600 baud.›     ›     Send comments, problems of any kind to:›     cp576@cleveland.freenet.edu›     ›     Include you votes for any of the following.  If any already exist let›     me know too.›     ›     Other possibilities:›     ›     XFD2DISK - xfd to disk possibly with XModem recieve.  I will do this›     first, since I need it.  Is there any other way to get a file out of a›     disk image?›     ›     DISK2ATR,ATR2DISK - What is in the 16 byte header of an .ATR file?›     ›     DCM2XFD/XFD2DCM - Discomm to XFD file and vice versa.  This would›     probably be useful more as an IBM program.  It probably wouldn't be›     too difficult to add to DISK2XFD.  I spent a while decoding DISKCOMM›     files, might as well put it to use.›     ›    On single drive systems with a command line type DOS, start it up›without parameters so you can swap disks.››     ›Other Programs to look for.  All support command line and menu based DOS's.››KEDIT E: based text editor supporting 40/80 column screens and horizonal›      scrolling to 127 characters.››KASM  Atari Macro Assembler and RA65 compatable M.L. Macro Assembler.›      Assembles to loadable or relocatable files.››KLINK LINK65 compatable linker.  Links files generated by RA65 and KASM.››KCONVERT Fast ascii<-->atascii converter.›